富凌變頻器DZB100M系列故障代碼詳表
發布時間：2019-07-31 11:22:03來源：
富凌變頻器DZB100M系列故障代碼詳表
| 故障代碼 | 故障現象/類型 | 故障原因 | 解決對策 |
| E004 | 加速中過電流 | 1.電機輸出側短路 2.加速時間太短 3.轉矩提升過高 4.變頻器輸出容量太小 | 1.檢查U-V-W到電機之配線是否絕緣不良; 2.增加加速時間 3.減低（F-54）轉矩提升設定值 4.更換較大輸出容量變頻器 |
| E005 | 運轉中過電流 | 1.電機輸出側短路 2.電機負載突增 3.變頻器輸出容量太小 | 1.檢查U-V-W到電機之配線是否絕緣不良 2.檢查電機是否過負載 3.更換較大輸出容量變頻器 |
| E006 | 減速中過電流 | 1.電機輸出側短路 2.減速時間太短 3.變頻器輸出容量太小 | 1.檢查U-V-W到電機之配線是否絕緣不良 2.增加減速時間 3.更換較大輸出容量變頻器 |
| E008 | 過負載 | 1.負載突增 2.電機堵轉 3.轉矩提升過高 4.變頻器輸出容量太小 | 1.檢查電機是否過負載 2.檢查電機是否有卡死現象 3.減低（F-54）轉矩提升設定值 4.更換較大輸出容量變頻器 |
| E009 | 電流異常 | 1.變頻器輸出容量太小 2.電機輸出側短路 3.加速時間太短 4.負載瞬間變化太大 5.電流輸出不平衡 | 1.檢查電機額定與變頻器輸出功率是否相符合 2.檢查變頻器與電機的聯機是否有短路現象或接地 3.增加加速時間(F-10,12) 4.檢查電機是否有超額負載 5.變頻器送修 |
| E00A | 過電壓 | 1.電源電壓過高 2.負載慣性過大或減速時間過短 | 1.檢查輸入電壓是否在變頻器額定輸入電壓范圍內，并監測是否有突波電壓產生 2.增加減速時間或加裝煞車電阻(選用) |
| E00d | 外部故障 | 外部故障功能端子閉合 | 清除故障來源后按“RESET”鍵即可 |
| E00E | 變頻器過熱 | 變頻器內部溫度過高，超過 保 護 準位 | 1.檢查環境溫度是否過高 2.檢查散熱片是否有異物，風扇有無轉動 3.檢查變頻器通風空間是否足夠 |
| CPU故障 | 內部存儲器IC資料讀出故障 | 1.按下RESET鍵將參數重置為出廠設定 2.變頻器送修 | |
| E011 | 啟動報警 | 內部繼電器未吸合（啟動時報警） | 檢查內部繼電器是否損壞 |
| E013 | 過轉矩 | 電機負載超過過轉矩檢出準位設定值 | 1.檢查電機負載是否過大 2.檢查過轉矩檢出位準設定值（F-60~62） |
| E014 | 控制線路故障 | 控制器 保 護 線路故障; | 1.檢查輸入電源電壓正常后重新開機 2.變頻器送修 |
| E015 | 檢測線路故障 | 變頻器檢測線路故障 | 1.重新上電試機 2.送廠維修 |
| E016(bb) | 端子故障 | 當外部多功能輸入端子(MI1-MI3)設定此一功能時，變頻器停止輸出 | 清除信號來源“bb”立刻消失; |
| E017 | 接地 保 護 保險絲故障 | 接地 保 護 ：變頻器有故障輸出現象 輸出端接地（接地電流高于變頻器額定電流的 50（%）以上時），功率模塊可能已經損壞 此 保 護 系針對變頻器而非人體 保險絲故障：由主電路板的LED指示燈顯示保險絲是否故障 | 接地 保 護 ：確定IGBT功率模塊是否損壞 檢查輸出側接線是否絕緣不良 保險絲故障：更換保險絲 確定IGBT功率模塊是否損壞 檢查輸出側接線是否絕緣不良 |
| E001 | TheAC drive detects that the DC bus voltage has fallen below its minimum value. | Check whether the input voltage falls within the ratedAC drive's input voltage. | |
| E004 | Over-current during acceleration: 1. Short-circuit at motor output. 2. Torque boost too high. 3. Acceleration time too short. 4. AC drive output capacity too small. | Check for possible poor insulation at the output line. Decrease the torque boost setting in F1-54. Increase the acceleration time. Replace with anAC drive with higher output capacity. | |
| E008 | 1.The AC drive detects excessive drive output current. 2.The AC drive can withstand up to 150（%） of the rated current for a maximum of 60 seconds. | Check whether the motor is overloaded. Reduce the torque compensation setting as set in F1-54. Increase theAC drive's output capacity. | |
| E009 | The over-current hardware trip circuit detects an abnormal increase in current. | Check whether the motor output power corresponds to the AC drive output power. Check the wiring connections between the AC drive and motor for possible short circuits. Increase theAcceleration time 1 and 2 (F1-10,12). Check for possible excessive loading conditions at the motor. After short-circuit being removed, if there is any abnormal conditions when operating the AC Motor Drive, it should be sent back to the agency or manufacturer. | |
| E00A | TheAC drive detects that the DC bus voltage has exceeded its maximum allowable value. | Check whether the input voltage falls within the ratedAC drive input voltage. Check for possible voltage transients. Bus over-voltage may also be caused by motor regeneration. Either increase the Decel time or add an optional braking resistor. Check whether the required braking power is within the specified limits. |
| 故障代碼 | 故障現象/類型 | 故障原因 | 解決對策 |
| E00d | The external terminal EF-DCM goes from ON to OFF. | The external terminal EF-DCM goes from ON to OFF. | |
| E00E | TheAC drive temperature sensor detects excessive heat. | Ensure that the ambient temperature falls within the specified temperature range. Make sure that the ventilation holes are not obstructed. Remove any foreign objects on the heatsinks and check for possible dirty heatsink fins. Provide enough spacing for adequate ventilation. | |
| E00F | AC drive E2PROM contains invalid data or can not be programmed. | Check the connections between the main control board and the power board. Reset drive to factory defaults. | |
| E011 | Realy contact don't work （Start-up warning） | Check whether the internal Realay is damaged. | |
| E013 | Motor overload. Check the parameter settings F1-60, 62.) | Reduce the motor load. Adjust the over-torque detection setting to an appropriate setting. | |
| E014 | Protection circuitry of hardware detected abnormal operation. | Remove power from the AC drive and then restore power. If H.P.F. fault appears again, the AC drive should be returned for service. | |
| E015 | Drive's internal circuitry abnormal. | Switch off power supply. Check whether the input voltage falls within the rated AC drive input voltage. Switch on theAC drive. | |
| E016 | External baseblock. AC drive output is turned off. | When the multi-function input 1 (2, 3)-DCM terminal goes from OFF to ON, the AC drive output will be turned off. | |
| E017 | Ground fault or fuse failure: Ground fault : The AC drive output is abnormal. When the output terminal is grounded (short circuit current is 50（%） more than the AC drive rated current), the AC drive power module may be damaged. The short circuit protection is provided for theAC drive protection, not user protection. 1. 2.Fuse failure: The fuse failure information will be displayed by the LED located on the power board. | Ground fault : 1. Check whether the IGBT power module is damaged. 2. Check for possible poor insulation at the output line. Fuse failure: 1. Replace Fuse. 2. Check whether the IGBT power module is damaged. 3. Check for possible poor insulation at the output line. |
鄭州變頻器 網址：http://www.cntjjp.com.cn